Amada Marvel 10.6" x 10" Horizontal Scissor Style Saw, Model HFA250W - NEW

Asset # 16208N
Serial # 65050403

Delivers Extraordinary Precision with High Accurate Material Indexing

5 HP

1-1/4" Blade

Automatic

NC Back Gauge

Self Diagnostics

Variable Blade Speed

Wheel Cover Limit Switch

FEATURES

Saw Head Frame
- The rigid 'C' section frame carries the mountings for the two band wheels, heavy-duty worm drive gear reducer, the band drive motor, and saw guide arm mounting supports.

Band Wheels & Drive System
- The band wheels are cast iron for long, productive life. The deflection free 1.38 inch (35 mm.) wheel spindles ensure the wheels run true regardless of tension stress or cutting loads. The spindle assemblies incorporate tapered roller bearings for greater rigidity and long service life. The wheel tracks the blade so that the back of the band is contacts the wheel flanges to support the band. The drive motor is coupled to the transmission through a variable speed pulley.

Wide Blade (1 1/4 inch, 34mm)
- The wider blade, for this capacity machine, can make full utilization of the large band drive motor (5 hp, 3.7 kW) when cutting all shapes and alloys.

Drive Wheel Transmission
- The drive wheel transmission is designed and built by Amada to provide high-efficiency speed reduction, which requires no external cooling, to deliver more power to the large diameter drive hub. This hub ensures that this developed torque is transferred to the blade with no strobing, enabling the machine to efficiently cut high alloys as well as free machining materials.

Pressure/Flow Feed Control
- The independent pressure and flow controls in series ensure the optimum cutting rate can be obtained regardless of section or alloy being cut. The pressure control determines the cutting force applied to the blade and the flow control sets the maximum fall rate of the head. For example, for difficult to machine materials the pressure is set higher than free machining alloys and the flow is set lower, as shown on the escutcheons above the control knobs.

Idler Wheel Motion Detector
- The wheel motion detector will turn off the blade drive in the case where a blade breaks or is jammed in the workpiece. This feature also prevents premature wear on the drive wheel from a stalled band.

NC Control of Cutting and Auto Cycle
- The NC index control provides greater flexibility and expanded capabilities compared to a The controller enables the operator to specify the index home position - forward and clamped or at the index position and open. The controller also determines the speed of the index vise motion forward and reverse. It provides independent ramp cycles for the forward and rear traverse. The speed ramp up and down for moving the work piece is slower when it is positioning the work piece than when it is moving without work. This feature provides more accurate indexing of the work piece.

Smart Multiple Index
- The machine control has the capability to make multiple full length index strokes until the length remaining to index is less than the full index stroke (15.8 in., 400mm.) the last index stroke is the remaining length.

Band Deviation Monitor ®
- This patented cutting control device can reduce scrap by warning when the blade is no longer cutting within the operator's settings for deviation. The allowable deviation limit is set by the operator independently for each direction. The digital deviation indicator will flash when the blade deviation exceeds either maximum. If the deviation continues to exceed the preset value the NC controller will stop the cutting, raise the saw head and display the exceeded deviation value.

Split Front Vise
- The work holding vise is split so that it clamps the work piece on both sides of the cutting plane. This additional support in front of the cutting plane minimizes the burr on the cut pieces.

Powered Chip Conveyor
- The powered chip conveyor auger automatically removes the saw chips from the saw while draining the cutting fluid back into the fluid reservoir. The automatic chip conveyor greatly reduces cleanup time and enables the machine to run longer without operator cleanup.

SPECIFICATIONS

Model		HFA250W
Cutting Capacity	Round (Diameter)	1.18"-10"	30-250 mm
Cutting Capacity	Rectangle (W x H)	10.6" x 10"	270 x 250 mm
Work Load Capacity		3,307 lbs	1,500 kg
Saw Blade	Blade Size (L x T x W)	11'6" x 0.042" x 1-1/4"	3505 x 1.1 x 34 mm
	Blade Speed	89-295 ft/min Stepless	27-90 m/min Stepless
	Tension Control	Hydraulic
Blade Control	Top Limit Setting	Automatic Setting with Quick Approach Feeler
Blade Control	Cutting Control	Hydraulic Pressure & Flow Control Valve
Vise Operation	Type	Front Split Vise and Rear Vise
Vise Operation	Control	Hydraulic Full-Stroke Cylinder
Motors	Saw Blade	5 HP	3.7 kW
	Hydraulic Pump	1 HP	0.75 kW
	Cutting Fluid Pump	1/4 HP	0.12 kW
Power Requirement	Power Supply Voltage	AC220V±10%, 3 PH, 60 Hz or AC440V±10%, 3 PH, 60 Hz
Power Requirement	Power Requirement	8kVA
Cutting Fluid	Tank Capacity	22.5 gal	85 liters
Cutting Fluid	Pump Type	Centrifugal Electric Pump
Hydraulic	Tank Capacity	7.9 gal	30 liters
	Pump Type	Variable-Discharge Vane Electric Pump
	Pump Capacity	4.0 gal/min	15 L/min
	Pressure Setting	384 psi	2.7 MPa (27 kgf/cm²)
Chip Disposal		Chip Conveyor
Material Index	Index Mechanism	Shuttle Vise
	Stroke	15.75"	400 mm
	Length	0.39-999.999"	10-9999.9 mm
	Number of Input Station	1-99
	Number of Cut-Off Pieces	1-9999
	Remnant Length	2.24" Plus Length of Parts	57 mm Plus Length of Parts
Machine Dimensions (W x L x H)	Head-Up Position	76.6" x 93.1" x 69.8"	1945 x 2366 x 1772 mm
Machine Dimensions (W x L x H)	Head Down Position	76.6" x 93.1" x 50.6"	1945 x 2366 x 1285 mm
Table Height		27.6"	700 mm
Machine Weight		3,310 lbs	1,500 kg

Saws Horizontal

Clausing Kalamazoo 12" x 18" Wet Semi-Automatic Horizontal Saw, Model MS1218VS

Ellis 10" x 11" Horizontal Saw, Model 1600 - NEW

DoAll 7" x 11" Dual Miter Manual Bandsaw, Model DS-280M

Marvel Spartan 13" x 14" Horizontal Scissor Saw with Programmable Controls, Model PA13-MPC - NEW

Amada Marvel 10.6" x 10" Horizontal Scissor Style Saw, Model HFA250W - NEW

Clausing Kalamazoo 13" x 19.6" Automatic NC Swivel Horizontal Saw, Model MS1319NC - NEW

Dake Johnson 10″ x 18″ Horizontal Bandsaw, Model J

Hyd-Mech 13” x 18” Horizontal Miter Saw, Model S-20P Series III

Marvel Spartan 22" x 28" Semi Automatic Horizontal Saw, Model PB2228 - NEW

Wellsaw 8” x 16” Horizontal Saw, Model 800

Marvel 15" x 24" Heavy Duty Miter Horizontal Saw, Model SA460WPC - NEW

Wellsaw 1000 Horizontal Saw

WF Wells Model W-9 Horizontal Saw

Kasto 14” x 14” Fully Automatic Horizontal Saw, Model HBA 360 AU

Clausing Kalamazoo 13" x 18" Semi-Automatic Swivel Horizontal Saw, Model MS1318SA - NEW

Marvel Spartan 22" x 24.5" Automatic Horizontal Saw with Programmable Controls, Model PA22-MPC - NEW

HE&M 25” x 30” Dual Post Column Horizontal Saw, Model F160LM-60

Wellsaw No. 8 Horizontal Band Saw

DoAll 16" x 16" Dual Column Tube CNC Bandsaw, Model TDC-400CNC - NEW

Marvel Spartan 14" x 14" Heavy Duty Horizontal Saw, Model PB 360 - NEW